How to build the Corris Rivett in My Winter Car? All parts and assembly process explained

The Corris Rivett is the project vehicle in My Winter Car, and building it is one of the game’s key goals.

When you purchase the Corris Rivett, you get an empty shell of the car. Thus begins your journey of building it up from scratch with various parts. This guide will provide you with all the information you need to make the Corris Rivett drivable.

How to build the Corris Rivett in My Winter Car

The Corris Rivett has over 100 parts to build the car from the ground up. These parts are divided into six broad categories. There’s no correct order for building the car. You can mix and match categories based on what parts you find.

Chassis and Suspension

• Subframe (front & rear)
• Control arms
• Coil springs
• Shock absorbers
• Steering rack
• Tie rods
• Spindles
• Hubs
• Brake discs
• Calipers

Engine and Drivetrain

• Engine block
• Crankshaft
• Pistons
• Head gasket
• Cylinder head
• Camshaft
• Carburetor or EFI system
• Alternator
• Starter
• Radiator
• Hoses
• Fuel pump
• Gearbox
• Clutch assembly
• Drive shafts
• Exhaust system

Mount and Body Panels

• Doors (L/R)
• Hood
• Trunk
• Fenders
• Bumpers
• Grille
• Headlights
• Taillights
• Windows
• Windshield

Winter-protection kits

• Car heater
• Blower
• Battery
• Windshield wipers
• Tires

Fluids

• Engine oil
• Coolant
• Brake fluid
• Fuel

Electrical Circuitry

• Battery terminals
• Alternator wiring
• Starter wiring
• Dashboard gauges
• Lights
• Heater controls

The Chassis should be your top priority since you won’t be able to add certain parts otherwise. To complete the Corris Rivett, you’ll have to get all the parts mentioned above. Before you can drive, here are some key things to ensure.

• Tightened all the bolts
• Fuel and Battery are fully charged
• All fluids have been filled
• Suitable tires in place
• Wipers active

Once done, you can then start the engine, and your car will be ready to move.

How to get Corris Rivett parts in My Winter Car

There are three major ways of obtaining the Corris Rivett parts in My Winter Car.

• Some parts are available from the same NPC who sells you the Corris Rivett. You can purchase them from him.
• Fleetari’s Ship is another excellent source for obtaining several parts required to complete the car.
• You’ll find plenty of parts via catalogue orders by going through adverts from the magazine. Once you place an order, the item will be available in two in-game days.

The post How to build the Corris Rivett in My Winter Car? All parts and assembly process explained appeared first on Destructoid.

The Firewood Cutter, aka the Lumber Conveyor, is an exceptional tool if you’re looking to sell and cut Firewood in My Winter Car.

This item can’t be used on its own, and you’ll need to use the tractor to do so. However, the job is easier said than done, and this guide will help you become a woodcutter in a few simple steps.

How to use the Lumber Conveyor in My Winter Car

The first task is to connect the Cutter to the Kekmet. It’s impossible to move the Lumber Conveyor from its stationary position without attaching it to your tractor. Hence, drive the tractor carefully and place it very close to the Conveyor. Keep the distance as minimal as possible, or else the alignment will be loose, and logs will fall.

You’ll find the rear hitch lever on the right side of the Kekmet. Use it to lower the attachment arms from the rear of the tractor. Get down, and click the connection point on the cutter (once the attachment arms have been lowered). If aligned properly, the cutter will connect with the Kekmet.

Next, use the PTO lever located to the left of the steering wheel of the Kekmet. Activate it to start the sdrive shaft and the Conveyor. If you want the cutter to work fast, go for a higher RPM. However, that will be less conducive to a longer cutting session.

How to cut the Firewood in My Winter Car

Once you have completed all the steps mentioned earlier in the guide, take a log from the wood pile. Then, place it in the cutter slot. The log will automatically split the logs into pieces based on how high the RPM is. The Conveyor will automatically place the Firewood in the trailer (don’t forget to attach it).

The post How to use the Firewood Cutter in My Winter Car appeared first on Destructoid.